Skip to content

Structure and Design

Roof Frame Design

When a project changes the shape of your home, the roof has to change with it. And when an existing roof starts to dip or crack, the framing underneath needs an expert's eyes.

When to Stop and Call

This is structural work. Nothing here is a do-it-yourself guide. If you see any of the following, stop what you are doing, keep people out of the space below and call a structural engineer or qualified contractor:

Open wood wall studs and roof trusses inside a home under construction
  • A ridge line or roof surface that has begun to sag or dip
  • A rafter, truss or beam that is cracked, split or pulling away from its connection
  • New, large cracks in walls or ceilings below the roof, or doors that have suddenly begun to stick upstairs
  • A roof deck that feels soft or bouncy, or damage from a fallen tree

Do not cut, notch, prop or jack any part of a roof frame to see if it helps. Raising or removing a load suddenly can make things much worse.

Problems in an Existing Roof Frame

The ridge line is not straight anymore

A healthy ridge reads as a straight line from the street. A dip or swayback can come from undersized original lumber, long-term water damage, rafters spreading at their base because ties are missing or have been removed, an extra layer of roofing, or a wall below that has been altered. Some old roofs took on a gentle curve decades ago and have held steady, while others are still moving. You cannot tell which from the ground.

An engineer can look at spans, connections and load paths and tell you how serious it is. If it has been checked and is stable, you may have time to plan. If it is new or getting worse, it cannot wait. The fix might mean adding framing, collar ties, new supports or, in bad cases, rebuilding part of the roof, always following a design specific to your house. Shingles that look wavy can also point to decking problems instead of rafters, which is another reason to have it looked at properly.

A cracked rafter spotted from the attic

Rafters crack along old knots, at notches someone cut for a duct or pipe, or after being overloaded or struck by a falling limb. Water can also rot them where they meet a leak. If a repair person or an inspector finds one, take a photo from a safe spot and arrange a professional review. Trusses are a separate matter: each piece depends on the others, and a cut or broken one needs a repair design from an engineer.

One damaged member with sound wood around it can often be repaired according to an engineer’s direction. Many damaged members, or rot along a whole section, usually points to rebuilding that section. If water caused it, the source has to be fixed too, which is where tracing the leak comes in. Cost and time depend on access, the extent of the damage, the engineer’s design, permits and how much roof must be opened.

Adding Weight to the Roof

Roof framing was sized for a certain load. Changes that add weight deserve a check first, even if the roof looks fine today.

Worker in a safety harness carrying a wood beam past roof sheathing and framing

Heavier roofing

Moving to tile, slate or another heavy product, or adding an extra shingle layer, can add considerable weight. Read about material choices under new roofing systems.

Solar panels

Panels and racks add load at their mounting points and need sound rafters beneath them. An older or damaged roof should be evaluated before anything is attached.

Equipment

HVAC units, water tanks or heavy storage in an attic concentrate weight on framing that may never have been meant to carry it. Trusses, in particular, generally have little spare capacity for this.

The answer can range from no changes needed to added framing. An engineer’s letter or a permit office may be required, and rules vary, so ask before ordering anything.

Adding On: Tying a New Roof Into an Old One

Roof framing for additions is where appearance and structure have to be settled together. The main question early on is how the new roof shape meets the old one: extending a line, stepping down with a lower roof, or creating a new gable or valley.

Carpenter in a hard hat cutting a framing board with a circular saw
  • Slope and height: matching the pitch looks natural, though the new ridge, ceiling heights or a window above can force a change
  • Load paths: the new roof’s weight has to travel down through walls and foundations, and an opened wall below may no longer be doing its old job
  • The joint: every new valley or wall junction is a new place for water to get in, and those details are covered on our flashing and valleys page
  • Old framing: when the existing roof is opened up, surprises such as past repairs, rot or undersized members may come to light
  • Ventilation: a new connection can block the attic airflow the old roof relied on

Plan it before the foundation or the walls are built, not at framing stage, because a roof shape that seemed easy on a sketch can cause real trouble later. We work with architects and designers on design-build projects, and install new roofing systems that match your structure, design and long-term goals. Our page on home additions covers the rest of the project. Time and cost depend on roof complexity, how much of the old roof gets opened, design and engineering, and permit review.

If your home is older, expect some extra caution. Pre-1978 paint on trim or walls being opened calls for lead-safe practices, and old insulation in the attic should be tested for asbestos before it gets disturbed.

Turning the Attic Into a Room

A big attic is tempting, but whether it can become living space depends on how the roof was framed. An attic with rafters and open space may be a real candidate. A web of angled wood, which means trusses, usually is not without major redesign, and those members should never be cut.

Then there is the floor. Attic joists are often sized to hold up a ceiling, not people and furniture, so they commonly need strengthening. Add headroom, stairs, a way out in a fire, insulation and ventilation, and it quickly becomes a design project. Requirements vary, so the local permit office and a design professional need to be part of the early conversation. Adding dormers for headroom means changing the roof itself, which again calls for an engineer. Ask about a review of what you have before you budget for finishes.

Who Should Be Involved

  • Ask whether a structural engineer has reviewed the plan, and who hired them
  • Ask to see stamped or written drawings if the local permit office requires them
  • Check that framing and roofing are coordinated under one plan, so that nobody is left guessing about the joint
  • Check insurance covers structural work, and what licensing applies
  • Ask how the open roof will be protected from rain during the job

Twelve25 Construction is licensed and insured, can help with permits, and offers a free consultation with a detailed scope of work once the design is settled. We work with trusted partners in architecture and design. For your specific situation, send us what you know and we will tell you plainly what it needs first. General remodeling questions are covered on our custom renovations page.

Illustration of a block house model with its roof rafters exposed, on top of rolled plans

Roof Framing FAQs

Is a sagging roof dangerous?

It can be. Treat it as serious until someone qualified has examined it. Keep people out of the space below if the sag is new, growing, or came with cracking sounds or new interior cracks.

Who do I call first, a roofer or an engineer?

For sagging or cracked framing, start with a structural engineer or a contractor who can bring one in. A roofer can replace the surface, but should not be judging the framing alone.

Can a new roofline match my existing house?

Usually it can be made to look close, but the pitch, overhangs and shingle color all need attention. A designer’s sketch early on shows you what is possible.

Do I need a permit to change the roof structure?

Quite likely, though rules vary by location. Check with the local permit office. We help with permits as part of a project.

Can I convert an attic that has trusses?

Usually not without a substantial redesign by an engineer. Do not cut any part of a truss while exploring the idea.

Serving Nashville, TN

We provide roofing in Nashville, TN and nearby communities such as Franklin, Brentwood, Hendersonville, Murfreesboro and Mount Juliet. See all of the areas we serve or call (615) 478-5705.

Let’s Build Something Great Together.

Ready to start your next construction or remodeling project? Tell us about your space and request a free estimate.

Nashville (615) 478-5705Atlanta (770) 669-1314